After wide-width nonwoven fabric arrives, a common acceptance practice is to cut a piece, weigh it, and accept the roll if the basis weight reading looks correct. The problem is that basis weight is not evenly distributed across the full width. A single sample only represents the location where it was cut.
Dong Guan Hendar Cloth Co., Ltd. can produce PP spunbond nonwoven fabric as light as 12 g/m². Its production lines have base widths of 2.4 m and 3.2 m, while wider 4.8 m and 6.4 m formats are achieved through splicing. Each time the width increases, there is more room for accumulated cross-direction variation, making the sampling position less arbitrary.
I. Understanding the mechanism: how non-uniformity arises
Basis weight refers to mass per unit area. During the spinning, drawing, web formation, and thermal bonding processes, it is difficult to distribute fibers perfectly evenly across the width. Edge areas and the center usually differ in web formation. This is not necessarily a defect, but an inherent fluctuation in continuous production.
The wider the fabric, the greater the potential for cross-direction variation. This applies to base widths of 2.4 m and 3.2 m, and even more so to 4.8 m and 6.4 m widths produced by splicing, which introduce an additional variable at the joint area.
|
One sample cannot represent the entire roll. Therefore, a single-point measurement reflects only the result at one location, not the overall level of the roll or the full width. Using a single point to represent the whole is not a sound basis for judgment. |
II. How to arrange sampling points: covering three directions
Cross-direction coverage. At a minimum, samples should cover both edges and the center, so the data reflect the cross-direction distribution rather than a randomly cut position.
Machine-direction coverage. The beginning, middle, and end of a roll are not identical. Roll changes, joints, and start-up/shut-down sections deserve separate attention.
Joint areas. For spliced wide-width fabric, samples should be taken separately on both sides of the joint. This area often differs from the main body in basis weight and strength performance, and is a key weak point for wind resistance and tear resistance.
|
There is no universal number of sampling points. It should be noted that the exact number and layout of sampling points have no industry-wide standard. They should be agreed between buyer and supplier based on the order and end use, rather than copied from another company’s practice. |
III. How to judge after sampling: look at distribution, not a single point
Once a set of data is obtained, judgment should be based on the overall distribution, not on any single value. Therefore, three items should be agreed in advance:
Judgment criteria. Whether acceptance is based on the average value, the extreme value, or the proportion of values falling within a specified range. Different criteria may lead to opposite conclusions from the same dataset.
Tolerance range. Tolerances for basis weight and width should be confirmed by both parties according to the order. A single uniform figure detached from the product and its end use is not appropriate.
Sampling method. The sampling tool, sample area, and weighing conditions must be consistent; otherwise, the data are not comparable.
|
Without agreed criteria, numbers only look professional. Unless these three items are settled, sampling has limited meaning; otherwise, the measured figures merely appear professional. |
IV. Agree on the sampling plan during the sampling stage
Dong Guan Hendar Cloth Co., Ltd. follows a nine-stage delivery process: requirement confirmation, specification translation, sampling and validation, customer confirmation, sealed or retained samples, production control, in-process and finished-product inspection, bulk comparison and delivery, and abnormality closure. Sampling positions and judgment criteria belong to the second stage, “specification translation,” with corresponding batch records retained during inspection. At this stage, Hendar and the purchaser should confirm how many cross-direction points to take, which machine-direction sections to sample, and whether joints are sampled separately.
This aligns with the practice of demanding customers. A leading mattress-industry customer (name kept anonymous) inspects different batches and basis weights, including ash content, to assess long-term stability. If an order has clear requirements for width uniformity, it is advisable to include sampling positions, quantity, and judgment criteria in the specification confirmation document.
FAQs
Q: How many sampling points are sufficient for wide-width nonwoven fabric?
A: There is no universal number. It depends on width, end use, and the agreed judgment criteria. A practical approach is to first agree on cross-direction and machine-direction zoning, then clarify whether acceptance is based on average or extreme values, rather than fixing a point count in advance.
Q: Should the joint area of spliced wide-width fabric be sampled separately?
A: Yes. The joint area usually differs from the main body in basis weight, strength, and wind resistance, and is a weak point in wide-width coverage. It should be sampled and checked separately.
Q: If several sampling readings vary, how do we determine whether the material is acceptable?
A: Not necessarily. Judgment should follow the mutually agreed tolerance, sampling method, and acceptance criteria. Without an agreed acceptance framework, simply observing “uniformity” is insufficient to reach a conclusion.
After wide-width nonwoven fabric arrives, a common acceptance practice is to cut a piece, weigh it, and accept the roll if the basis weight reading looks correct. The problem is that basis weight is not evenly distributed across the full width. A single sample only represents the location where it was cut.
Dong Guan Hendar Cloth Co., Ltd. can produce PP spunbond nonwoven fabric as light as 12 g/m². Its production lines have base widths of 2.4 m and 3.2 m, while wider 4.8 m and 6.4 m formats are achieved through splicing. Each time the width increases, there is more room for accumulated cross-direction variation, making the sampling position less arbitrary.
I. Understanding the mechanism: how non-uniformity arises
Basis weight refers to mass per unit area. During the spinning, drawing, web formation, and thermal bonding processes, it is difficult to distribute fibers perfectly evenly across the width. Edge areas and the center usually differ in web formation. This is not necessarily a defect, but an inherent fluctuation in continuous production.
The wider the fabric, the greater the potential for cross-direction variation. This applies to base widths of 2.4 m and 3.2 m, and even more so to 4.8 m and 6.4 m widths produced by splicing, which introduce an additional variable at the joint area.
|
One sample cannot represent the entire roll. Therefore, a single-point measurement reflects only the result at one location, not the overall level of the roll or the full width. Using a single point to represent the whole is not a sound basis for judgment. |
II. How to arrange sampling points: covering three directions
Cross-direction coverage. At a minimum, samples should cover both edges and the center, so the data reflect the cross-direction distribution rather than a randomly cut position.
Machine-direction coverage. The beginning, middle, and end of a roll are not identical. Roll changes, joints, and start-up/shut-down sections deserve separate attention.
Joint areas. For spliced wide-width fabric, samples should be taken separately on both sides of the joint. This area often differs from the main body in basis weight and strength performance, and is a key weak point for wind resistance and tear resistance.
|
There is no universal number of sampling points. It should be noted that the exact number and layout of sampling points have no industry-wide standard. They should be agreed between buyer and supplier based on the order and end use, rather than copied from another company’s practice. |
III. How to judge after sampling: look at distribution, not a single point
Once a set of data is obtained, judgment should be based on the overall distribution, not on any single value. Therefore, three items should be agreed in advance:
Judgment criteria. Whether acceptance is based on the average value, the extreme value, or the proportion of values falling within a specified range. Different criteria may lead to opposite conclusions from the same dataset.
Tolerance range. Tolerances for basis weight and width should be confirmed by both parties according to the order. A single uniform figure detached from the product and its end use is not appropriate.
Sampling method. The sampling tool, sample area, and weighing conditions must be consistent; otherwise, the data are not comparable.
|
Without agreed criteria, numbers only look professional. Unless these three items are settled, sampling has limited meaning; otherwise, the measured figures merely appear professional. |
IV. Agree on the sampling plan during the sampling stage
Dong Guan Hendar Cloth Co., Ltd. follows a nine-stage delivery process: requirement confirmation, specification translation, sampling and validation, customer confirmation, sealed or retained samples, production control, in-process and finished-product inspection, bulk comparison and delivery, and abnormality closure. Sampling positions and judgment criteria belong to the second stage, “specification translation,” with corresponding batch records retained during inspection. At this stage, Hendar and the purchaser should confirm how many cross-direction points to take, which machine-direction sections to sample, and whether joints are sampled separately.
This aligns with the practice of demanding customers. A leading mattress-industry customer (name kept anonymous) inspects different batches and basis weights, including ash content, to assess long-term stability. If an order has clear requirements for width uniformity, it is advisable to include sampling positions, quantity, and judgment criteria in the specification confirmation document.
FAQs
Q: How many sampling points are sufficient for wide-width nonwoven fabric?
A: There is no universal number. It depends on width, end use, and the agreed judgment criteria. A practical approach is to first agree on cross-direction and machine-direction zoning, then clarify whether acceptance is based on average or extreme values, rather than fixing a point count in advance.
Q: Should the joint area of spliced wide-width fabric be sampled separately?
A: Yes. The joint area usually differs from the main body in basis weight, strength, and wind resistance, and is a weak point in wide-width coverage. It should be sampled and checked separately.
Q: If several sampling readings vary, how do we determine whether the material is acceptable?
A: Not necessarily. Judgment should follow the mutually agreed tolerance, sampling method, and acceptance criteria. Without an agreed acceptance framework, simply observing “uniformity” is insufficient to reach a conclusion.